tag:blogger.com,1999:blog-23681518.post3042173217906481008..comments2023-10-14T04:05:08.546-07:00Comments on Diary of a Technocratic Anarchist: In spite of all my warnings...Forrest Higgshttp://www.blogger.com/profile/17208965471464716174noreply@blogger.comBlogger6125tag:blogger.com,1999:blog-23681518.post-81942190306340715722011-12-09T09:15:59.948-08:002011-12-09T09:15:59.948-08:00I use 0.5 mm layers largely out of practical exper...I use 0.5 mm layers largely out of practical experience. It is a simple matter to set the layer thickness thinner in the slice and dice software. That entails adjusting the polymer flow rate, too, however.Forrest Higgshttps://www.blogger.com/profile/17208965471464716174noreply@blogger.comtag:blogger.com,1999:blog-23681518.post-40717126929594181352011-10-11T10:36:19.259-07:002011-10-11T10:36:19.259-07:00Hi Forrest, How do you control the slice thickness...Hi Forrest, How do you control the slice thickness ( in your case it is 0.1mm and I am looking for 0.05mm) in the code?<br /><br />Thanks!Anonymousnoreply@blogger.comtag:blogger.com,1999:blog-23681518.post-32806533763373524022010-03-02T05:52:02.861-08:002010-03-02T05:52:02.861-08:00LOL! Well, I hope you find it useful, then, if no...LOL! Well, I hope you find it useful, then, if not directly than as a guide for what not to do. :-)Forrest Higgshttps://www.blogger.com/profile/17208965471464716174noreply@blogger.comtag:blogger.com,1999:blog-23681518.post-53457251280253988792010-03-02T02:49:00.661-08:002010-03-02T02:49:00.661-08:00thanks. :)
I don´t intend to use it but
there is ...thanks. :)<br /><br />I don´t intend to use it but<br />there is a great overlap between<br />the code I currently need to write and parts of what S&D already has to perform<br />(slicing and stl-reading).The Editorhttps://www.blogger.com/profile/01641247429615484542noreply@blogger.comtag:blogger.com,1999:blog-23681518.post-34871753998064891242010-03-01T14:37:10.171-08:002010-03-01T14:37:10.171-08:00I'm just trying to cut down on the hassles...
...I'm just trying to cut down on the hassles...<br /><br />"Curiouse question, but the minimization of the non extruding path moves, will it end up being in skeinforge? The largest thing I've noticed, specifically when using a .3mm tip, is the amount of 'grey moves', which your app doesn't end up doing."<br /><br />Um... I not getting what you're saying here. :-sForrest Higgshttps://www.blogger.com/profile/17208965471464716174noreply@blogger.comtag:blogger.com,1999:blog-23681518.post-54211430476676335402010-03-01T13:18:35.696-08:002010-03-01T13:18:35.696-08:00:-D I don't think your earlier one included a...:-D I don't think your earlier one included a way to get the source. I'm assuming people where hoping that it would be usable, contrary to your warnings, out of the box.<br /><br />Curiouse question, but the minimization of the non extruding path moves, will it end up being in skeinforge? The largest thing I've noticed, specifically when using a .3mm tip, is the amount of 'grey moves', which your app doesn't end up doing.Thomas Charronhttps://www.blogger.com/profile/18315564747479470830noreply@blogger.com